Spend the extra few bucks on the wider. Most suppliers sell two sizes of starter, 2-1/2 in. It protects the sheathing from rain, snow and pests. Below the top of the foundation, but the lower the vinyl siding is installed, the better. The bottom of the starter strip (the part the bottom panel hooks on to) should be at least 1 in.Step 2: Hook your tool underneath the siding and pull down to start. Sheathing NailabilityStep by Step Instructions Step 1: Obtain a vinyl siding tool. Some manufacturers of vinyl siding do not recommend the use of drop-in backers with certain vinyl siding configurations. As an alternative, installation of specific types of drop-in contoured foam underlayments for various styles of vinyl siding are available. Vinyl siding must never be applied directly to studs without sheathing. Consult local building codes for sheathing requirements.Water-resistive BarrierThen you would install your fiber cement corner and window trim. In this case, the fastener would have to be long enough to penetrate through the sheathing and 1 1/4” (32mm) into the wood framing. But foam plastic sheathing does not contribute toward holding the fastener, so its thickness cannot be counted toward the total. The thickness of wood sheathing counts toward the total thickness that the fasteners must penetrate into nailable material, usually 1 1/4” (32mm). Quick Tips For Installation, Operation And Adjustments View How-To Videos.Vinyl siding can be installed over common wood sheathings such as plywood, oriented strand board (OSB), or other materials (e.g., foam plastic insulating sheathing). Step 4: Finish with a tap of the hand to tighten.Wood Siding Installation Instructions installing log siding, paneling, trim, corners, and more Cabin in the Woods Installation of our Prefinished 1×6 Knotty Pine Paneling NOTE: The individual siding installation videos for the Log Siding , Paneling , Corners , and D-trim applications are available on About Windows Doors Wall Systems Videos Gallery Find Us Careers.
Refer to Important Notes for more information on water-resistive barriers. Do not overdrive the nails.Vinyl siding should be installed over a continuous water-resistive barrier to stop the intrusion of incidental water. Use galvanized siding nails and make sure that the nails penetrate a minimum of 1-1/4-inches into the framing. Total all of the measurements for the areas to be sided. The area to be sided can be determined by measuring the height and width of the house, including windows (Fig. All houses can be broken down into shapes of rectangles or triangles, or a combination of both. Flashing should also be applied to inside and outside corners, and the intersection of walls and roofing to prevent water infiltration. Eric is currently serving as the chair of the VSI Sustainability and Recycling committee and is committed to always looking for opportunities to create a better experience for the customer and planet.Code-compliant flashing should be integrated with the water-resistive barrier and applied around windows, doors, and other openings. FlashingOur Product Install Trainer has over 20 years of Installation experience. Add siding to all material estimates to allow for waste, depending on the pitch of the roof and other house-specific factors. To estimate the amount of starter strip required, measure the linear feet around the entire base of the house. If the windows and doors are extremely large (such as a garage or sliding glass doors), some deductions can be made (Fig. Including them will provide an allowance factor for waste. Make sure the panels are fully locked along the length of the bottom, but do not force them up tight when fastening. Whether using a nail, screw, or staple to fasten the siding, the following basic rules must be followed: Every 100 square feet (9.29 square meters) is called a “square” for ordering purposes.Vinyl siding can expand and contract 1/2” (12.7mm) or more over a 12’ 6” (3.81m) length during normal, year-round changes in temperature. When fastening, start in the center of the panel and work toward the ends. Tight nailing, screwing, or stapling will cause the vinyl siding to buckle with changes in temperature (Fig. Allow approximately 1/32” (0.8mm) clearance (the thickness of a dime) between the fastener head and the vinyl. These distances may be increased if the manufacturer permits greater spacing based on wind load testing. Space the fasteners a maximum of 16” (406mm) apart for horizontal siding panels, every 12” (305mm) for vertical siding panels, and every 8” to 12” (203mm to 305mm) for accessories. Drive fasteners straight and level to prevent distortion and buckling of the panel (Fig. Roblox jailbreak speed hack downloadThe manufacturer may permit the use of staples as an alternative to nails. Corrosion-resistant, self-tapping sheet metal typeIf staples are being used instead of nails or screws, consult your local building codes. Screws must be able to penetrate no less than 1 1/4” (32mm) into framing or furring and should be: Screws must be centered in the slot with approximately 1/32” (0.8mm) space between the screw head and the vinyl. If a nail slot does not allow centering/securing into a nailable surface, use a nail hole slot punch to extend the slot and allow centering of the fastener.Screw fasteners can be used if the screws do not restrict the normal expansion and contraction movement of the vinyl siding panel on the wall. Place all other fasteners in the center of the slots. Siding Videos Free Movement OfMake sure the line is level by using a line level or a 4’ (1.2m) level. Attach a chalkline go to the next corner and pull the line taut. Determine the lowest point of the wall that will be sided from that point, measure up 1/4” (6.4mm) less than the width of the starter strip and partially drive a nail at one corner. Be wide enough in the crown to allow free movement of the siding (approximately 1/32” away from the nailing hem).In order for the siding to be installed properly in a level fashion, the starter strip at the bottom of the wall must be level. Penetrate not less than 1 1/4” (32mm) into framing or furring, or as specified in the manufacturer’s instructions. Not be less than 16-gauge semi-flattened to an elliptical cross- section.
0 Comments
Leave a Reply. |
AuthorAndrea ArchivesCategories |